MSF: Two LTIs – a slip and a fall, and trapping a thumb

  • Safety Flash
  • Published on 18 December 2018
  • Generated on 2 December 2024
  • IMCA SF 28/18
  • 3 minute read

The Marine Safety Forum (MSF) have recently released two safety alerts relating to lost time injuries (LTIs).  These are Safety Alert 18-27 and Safety Alert 18-24.

Incident 1: fractured toe

A crew member was going to a lower deck using an external stairway.  He was holding a bucket in one hand and holding the handrail with the other.  As he descended the staircase, his foot slipped off the step, causing him to fall.  In order to prevent further slipping down the remaining steps, he put his left foot in the space between the upright stanchions to break the falling motion, and as a result broke his toe.

The weather conditions were dry, and the vessels’ movement was not excessive.  The injured person was wearing appropriate footwear. 

Slip on stairway
External stairway
Lack of additional anti-slip grip strip on steps

Why did it happen? What were the causes?

The MSF notes that the only potential problem could have been an ineffective grip on the steps; the vessel had the standard perforated steps found on many vessels, however, there was no additional anti-slip grip strip.

What actions were taken?

  • Check that the anti-slip design or measures remain fit for purpose, and that they have not been painted over or worn – check it is still effective.
  • During wet weather or when decks and surfaces are wet, particular care should be taken to use the ‘trailing hand’ technique or the ‘one hand for the ship and one for yourself’.
  • Always wear appropriate personal protective equipment (PPE).

Incident two – squeezed thumb

A crew member was opening a watertight door into the bow thruster room.  As he placed his hand on the operating handle, he placed the other hand on the watertight door framework opposite.  As the door opened, his thumb was squeezed between the frame plating and the door housing.

What happened?

The injured person placed his hand on the opposite side of the door to steady himself, just in case of vessel movement.  However, the framework provides a flat surface and is easily mistaken as a ‘safe spot’ to place a hand when operating the operating lever.

Crewman in watertight door frame
Position of thumb in door frame
Door frame

What actions were taken?

  • Ensure all new crew members undertake a familiarisation tour of the vessel, effectively highlighting potential hazards (particularly, moving machinery, stored energy situations and equipment etc.).
  • Encourage crew members to ask questions if any task or part of their role is not understood.
  • All new crewmembers onboard should be supervised – this is key in providing trainees with a safe working environment. All supervisors are encouraged to ensure close mentoring and supervision.
  • Highlight hazards surrounding the weather tight and watertight doors onboard.
  • Add hazard markings to the door frame (as demonstrated in the above photos).
  • Concentrate on the task at hand – concentration is vital in ensuring every crew member departs the vessel in the same condition they joined.

Latest Safety Flashes:

LTI: Finger injury during emergency recovery of ROV

A worker suffered a serious finger injury when their finger was caught between a crane wire and the recovery hook on an ROV.

Read more
BSEE: recurring hand injuries from alternative cutting devices

The United States Bureau of Safety and Environmental Enforcement (BSEE) has published Safety Alert 487.

Read more
NTSB: Crane wire failure

The National Transportation Safety Board of the United States (NTSB) published "Safer Seas Digest 2023".

Read more
Hot work performed outside of Permit to Work (PTW) boundary limit

A near miss occurred when a third-party contractor working removed a trip hazard from the vessel main deck, using a cutting torch and grinding disc.

Read more
Vital safety information (height of vehicle) found incorrect

“Height of vehicle” information displayed on a truck, was found to be incorrect.

Read more

IMCA Safety Flashes summarise key safety matters and incidents, allowing lessons to be more easily learnt for the benefit of the entire offshore industry.

The effectiveness of the IMCA Safety Flash system depends on the industry sharing information and so avoiding repeat incidents. Incidents are classified according to IOGP's Life Saving Rules.

All information is anonymised or sanitised, as appropriate, and warnings for graphic content included where possible.

IMCA makes every effort to ensure both the accuracy and reliability of the information shared, but is not be liable for any guidance and/or recommendation and/or statement herein contained.

The information contained in this document does not fulfil or replace any individual's or Member's legal, regulatory or other duties or obligations in respect of their operations. Individuals and Members remain solely responsible for the safe, lawful and proper conduct of their operations.

Share your safety incidents with IMCA online. Sign-up to receive Safety Flashes straight to your email.