BSEE: Improper use and application of high-pressure hoses

  • Safety Flash
  • Published on 29 August 2023
  • Generated on 3 September 2025
  • IMCA SF 21/23
  • 2 minute read

The United States Bureau of Safety and Environmental Enforcement (BSEE) has published Safety Alert 465 relating to the improper use and application of high-pressure hoses.

What happened?

During a recent offshore inspection, a BSEE inspector observed operator personnel installing a 30m high-pressure hose, with a Maximum Working Pressure (MWP) of 5000 psi, to test pressure safety valves on pipeline pumps.

The hose used was designed for hydraulic fluid and was not suitable for high-pressure nitrogen; when nitrogen gas at 2500 psi was injected into the hydraulic hose, the hose blistered, allowing nitrogen gas to leak.

incompatible hydraulic hose blistered during use; hose with application information

BSEE recommendations

BSEE recommends operators and their contractors, where appropriate, consider:

  • Selecting hoses based on size, temperature, application, material to be conveyed, pressure, ends or couplings, and delivery.

  • Sizing the inside diameter (ID) and outside diameter (OD) appropriately to minimise pressure loss and reduce heat generation.

  • Choosing the appropriate hose size to match the new hose or referencing the original equipment manufacturer (OEM) for specifications of the equipment requiring the hose.

  • Ensuring the operating temperature of the hose is similar in temperature to the fluid and ambient temperatures. Both high and low temperatures can have a significant effect on the efficiency, performance, and safety of the hose. Also, check for hot surfaces or hot exhaust in the area where the hose will be installed and consider re-routing the hose if a heat shield cannot be installed.
  • Ensuring the hose is correct for the gas or fluid being carried.

  • Checking for compatibility between the fluid and the hose materials, along with connections, couplings, and O-rings.

  • Following manufacturer recommendations for hose inspection and replacement intervals. Frequent fluctuations in pressure and poor storage conditions may reduce hose life; consider these variations when determining replacement intervals for preventative maintenance.

  • Immediately stopping usage or replacing hoses when they become damaged, cracked, cut, abraded, blistered, soft, kinked, crushed, flattened, or twisted.

  • Always properly marking discontinued service hoses for disposal and quarantining them – storing them separately from new service hoses.

  • Ensuring work permits and job safety analyses address the risks involved in working closely with pressurised hoses.

  • Notifying personnel of the hazards of working around pressurised hoses and installing warnings and barriers.

Members may wish to refer to:

Latest Safety Flashes:

UK HSE: Motion Compensated Gangways Auto-Retraction

The UK Health and Safety Executive (HSE) has published Safety Notice ED03-2025

Read more
Brazil: diver permanently disabled after decompression illness

Conviction of diving company upheld as work accident suffered by a diver who lost strength in his upper limbs and the ability to move, requiring permanent use of a wheelchair.

Read more
Diver reports unwell post-dive: non-decompression illness

A diver experienced a dizzy spell about one hour after completing a diving operation

Read more
Shore-side crane boom collides with vessel mast

During shipyard lifting operations, the boom of a dock crane made contact with the vessel mast.

Read more
Injury sustained while operating steel lifting magnet

While preparing to transfer steel plates using a steel lifting magnet, a crew person was injured.

Read more

IMCA Safety Flashes summarise key safety matters and incidents, allowing lessons to be more easily learnt for the benefit of the entire offshore industry.

The effectiveness of the IMCA Safety Flash system depends on the industry sharing information and so avoiding repeat incidents. Incidents are classified according to IOGP's Life Saving Rules.

All information is anonymised or sanitised, as appropriate, and warnings for graphic content included where possible.

IMCA makes every effort to ensure both the accuracy and reliability of the information shared, but is not be liable for any guidance and/or recommendation and/or statement herein contained.

The information contained in this document does not fulfil or replace any individual's or Member's legal, regulatory or other duties or obligations in respect of their operations. Individuals and Members remain solely responsible for the safe, lawful and proper conduct of their operations.

Share your safety incidents with IMCA online. Sign-up to receive Safety Flashes straight to your email.