Near miss: dislodged grating with potential fall to sea

  • Safety Flash
  • Published on 30 April 2024
  • Generated on 12 December 2024
  • IMCA SF 09/24
  • 2 minute read

A section of Glass Reinforced Plastic (GRP) grating on a vessel dislodged and dropped to sea.

What happened?

A section of Glass Reinforced Plastic (GRP) grating on a vessel dislodged and dropped to sea. The incident occurred when a welder was on the grating passing a welding hose connection to a level further up, during preparations for work activities. The welder arrested their fall on a support beam and recovered without assistance to a safe position. The failed grating section fell 5.5m to sea and was lost. The welder, who did not suffer any injuries, reported the near miss. Operations nearby were suspended to allow follow up investigation and for the worksite team to complete a full review and “Time Out for Safety”.

dislodged grating on vessel
Dislodged grating on vessel
Dislodged grating on vessel

What went wrong?

  • The securing clips provided, which should have held the gratings in place, were not spaced correctly nor fixed securely to the framework.
  • Two of the securing clips were missed from the original installation design.
  • No-one spotted that the grating section was installed with an overhang on one end. As the welder stepped on this area, the forces allowed for the grating to tip and fall to the sea.

What went right?

  • The individual managed to catch himself and recovered to safety.
  • The incident was reported, and the investigation conducted quickly, corrective actions taken immediately.

What can we learn?

The grating fastenings or fixings were not identified or included within the vessel planned maintenance system. There was no routine inspection or visual check of the dimensional fit or condition of the securing clips. Consequently, over the installation period the grating became insecure, without the change being detected.

Actions

Our Member took the following actions:

  • Changes to planned maintenance system for grating and fixings, and amendment of safety checklists for area.
  • Added grating to future DROPS surveys, particularly on areas where work on split levels occurs, where the risk of serious personal injury may occur from falls and where potential for significant dropped objects exists.
  • Future grating design should follow good practice guidance for load capacity, fastenings and the avoidance of overhangs that may create a cantilever effect.
  • Changes to grating should be pre-approved by vessel Captain or Chief Engineer, temporary or permanent modifications should not be performed without approvals.

Latest Safety Flashes:

LTI: Finger injury during emergency recovery of ROV

A worker suffered a serious finger injury when their finger was caught between a crane wire and the recovery hook on an ROV.

Read more
BSEE: recurring hand injuries from alternative cutting devices

The United States Bureau of Safety and Environmental Enforcement (BSEE) has published Safety Alert 487.

Read more
NTSB: Crane wire failure

The National Transportation Safety Board of the United States (NTSB) published "Safer Seas Digest 2023".

Read more
Hot work performed outside of Permit to Work (PTW) boundary limit

A near miss occurred when a third-party contractor working removed a trip hazard from the vessel main deck, using a cutting torch and grinding disc.

Read more
Vital safety information (height of vehicle) found incorrect

“Height of vehicle” information displayed on a truck, was found to be incorrect.

Read more

IMCA Safety Flashes summarise key safety matters and incidents, allowing lessons to be more easily learnt for the benefit of the entire offshore industry.

The effectiveness of the IMCA Safety Flash system depends on the industry sharing information and so avoiding repeat incidents. Incidents are classified according to IOGP's Life Saving Rules.

All information is anonymised or sanitised, as appropriate, and warnings for graphic content included where possible.

IMCA makes every effort to ensure both the accuracy and reliability of the information shared, but is not be liable for any guidance and/or recommendation and/or statement herein contained.

The information contained in this document does not fulfil or replace any individual's or Member's legal, regulatory or other duties or obligations in respect of their operations. Individuals and Members remain solely responsible for the safe, lawful and proper conduct of their operations.

Share your safety incidents with IMCA online. Sign-up to receive Safety Flashes straight to your email.