Lifeboat drill – near casualty

  • Safety Flash
  • Published on 16 September 2011
  • Generated on 5 December 2024
  • IMCA SF 10/11
  • 3 minute read

An incident has been brought to IMCA’s attention in which a lifeboat was accidentally dropped into the sea.

What happened?

The incident occurred during a lifeboat drill at sea in good weather conditions. The starboard lifeboat was lowered to the embarkation deck. In this operation the top link of the forward chain for the connection between the davit floating block and the hook on the lifeboat parted, such that the entire load of the lifeboat was transferred to the aft hook/chain. As the aft chain could not withstand this weight, it parted and the lifeboat was dropped into the sea. At the time of the incident no crew members were onboard the lifeboat and thus there were no injuries. However, the lifeboat itself was considered a total loss due to extensive damage caused by the fall.

As lifeboats are often the primary method of evacuation from many vessels, the importance of maintaining the lifeboats to the highest standard cannot be over-emphasised. This safety flash highlights the importance of thorough inspection and maintenance of lifeboats and their associated launching equipment.

sequence of images illustrating the equipment failure

Figure: Sequence of images illustrating the equipment failure

 

What were the causes?

Investigation identified that it is likely that the top link of the forward chain parted due to corrosion or damage of the welding of the link such that the load was no longer distributed to both sides of the link. As the links/chain were painted, it was probably difficult to detect the fracture that had developed over time.

Lessons learnt

The following lessons, applicable to all vessels using chain links as part of the load transmission from the davit or davit block to the lifeboat hook, were drawn from the incident:

  • Chains should be replaced at regular intervals and/or tested by DPI/Ultrasonic testing at regular intervals to eliminate/detect parts with potential risk (although not required by the International Convention for the Safety of Life at Sea (SOLAS)), and this should then be included in the vessel maintenance system.

  • The lifeboat chain, hooks and release system should be inspected and maintained according to manufacturers’ recommendations, and should be included in the vessel maintenance system.

  • It is recommended that lifeboats are lowered without personnel onboard and boarding then carried out after the boat has been lowered, unless the boat is to be used for an emergency situation as directed by the master.

Actions

The following actions were taken:

  • Identification and inspection of all lifeboat equipment using chain links as part of the load transmission from davit or davit block to lifeboat hook.

  • Review of adequacy of inspection level and frequency as part of planned maintenance routines.

Latest Safety Flashes:

LTI: Finger injury during emergency recovery of ROV

A worker suffered a serious finger injury when their finger was caught between a crane wire and the recovery hook on an ROV.

Read more
BSEE: recurring hand injuries from alternative cutting devices

The United States Bureau of Safety and Environmental Enforcement (BSEE) has published Safety Alert 487.

Read more
NTSB: Crane wire failure

The National Transportation Safety Board of the United States (NTSB) published "Safer Seas Digest 2023".

Read more
Hot work performed outside of Permit to Work (PTW) boundary limit

A near miss occurred when a third-party contractor working removed a trip hazard from the vessel main deck, using a cutting torch and grinding disc.

Read more
Vital safety information (height of vehicle) found incorrect

“Height of vehicle” information displayed on a truck, was found to be incorrect.

Read more

IMCA Safety Flashes summarise key safety matters and incidents, allowing lessons to be more easily learnt for the benefit of the entire offshore industry.

The effectiveness of the IMCA Safety Flash system depends on the industry sharing information and so avoiding repeat incidents. Incidents are classified according to IOGP's Life Saving Rules.

All information is anonymised or sanitised, as appropriate, and warnings for graphic content included where possible.

IMCA makes every effort to ensure both the accuracy and reliability of the information shared, but is not be liable for any guidance and/or recommendation and/or statement herein contained.

The information contained in this document does not fulfil or replace any individual's or Member's legal, regulatory or other duties or obligations in respect of their operations. Individuals and Members remain solely responsible for the safe, lawful and proper conduct of their operations.

Share your safety incidents with IMCA online. Sign-up to receive Safety Flashes straight to your email.