A Member has reported two near miss incidents involving potential dropped objects.

What happened?

The objects were left on top of a temporary buoyancy module (TBM) during the installation of a tension leg platform (TLP).

In the first incident, two subsea lamps (each weighing 10kg in the air) were discovered on top of the TBM after it was retrieved back to deck. In the second incident, during an inspection of the top of a TBM, also after it was retrieved back to deck, a rigging crew discovered a wire cable retaining pin (weighing 10 kg in the air) lying loose on top of the upper bumper.

Incident 1 – Two temporary subsea lamps found on top of the TBM

subsea lights fixed to steel support
TBM

What went wrong? What were the causes?

An investigation discovered that the lamps were temporarily fixed to the TBM by the diving team, and should have been removed after they had finished their task in accordance with their post installation dive tasks. All other subsea lamps used during the task had been removed.

  • Not all subsea lamps were recovered as per post-installation dive tasks.
  • The missing subsea lamps were not identified immediately.
  • The company was unaware of the missing subsea lamps; there was no notification given by the subcontractor.
  • There was no awareness of the possibility of loose equipment being left behind, causing a dropped object threat to the company lifting crew.

What actions were taken?

  • Ensure that subcontractor personnel are properly reminded of the company procedures for subsea material recovery.
  • Further emphasize to crew the importance of stop work authority and of speaking up when they see an unsafe condition – which in this case was found to be very effective.

Incident 2 – A wire cable retaining pin was found lying loose on top of the TBM

Retaining pin loose on top of TBM
Wire cable retaining pin

What went wrong? What were the causes?

Investigation discovered that the object was an ‘ROV friendly’ wire cable-retaining pin. The pin was used to retain a wire in a sheave from which a ball grab was suspended. In order to retrieve the ball grab, an ROV was used to remove the retaining pin. After removal of the pin, the ROV was to let go of the pin, which would then stay suspended under water hanging from a rope. As this pin was not lashed properly, it became loose and landed on top of the upper bumper.

  • Inadequate lashing using inappropriate rope made it possible for the pin to drop.

  • The importance of proper lashing was not acknowledged by the divers or the dive supervisor.

What actions would be taken?

This incident would be circulated as a lesson learned.

Latest Safety Flashes:

NTSB: Vessel crane contact with shore-side crane

The National Transportation Safety Board of the United States (NTSB) has published a report and an investigation.

Read more
Dropped pallet during forklift operation

A pallet containing a load weighing 500kg dropped off a flatbed truck in close proximity to a delivery driver.

Read more
Dropped object hazard: access hatch to the communication dome

During a routine scheduled safety inspection of the main mast, it was discovered that the access hatch to one of the communication domes had fallen off.

Read more
Lock out/Tag out and unauthorised electrical connections/disconnections
Read more
MAIB: Is your Lead-Acid battery safe?

The UK Marine Accident Investigation Branch has published Safety Digest 1/2025, consisting of lessons from recent Marine Accident Reports.

Read more

IMCA Safety Flashes summarise key safety matters and incidents, allowing lessons to be more easily learnt for the benefit of the entire offshore industry.

The effectiveness of the IMCA Safety Flash system depends on the industry sharing information and so avoiding repeat incidents. Incidents are classified according to IOGP's Life Saving Rules.

All information is anonymised or sanitised, as appropriate, and warnings for graphic content included where possible.

IMCA makes every effort to ensure both the accuracy and reliability of the information shared, but is not be liable for any guidance and/or recommendation and/or statement herein contained.

The information contained in this document does not fulfil or replace any individual's or Member's legal, regulatory or other duties or obligations in respect of their operations. Individuals and Members remain solely responsible for the safe, lawful and proper conduct of their operations.

Share your safety incidents with IMCA online. Sign-up to receive Safety Flashes straight to your email.