Fire in engine space on crew transfer vessel (CTV)

  • Safety Flash
  • Published on 30 June 2014
  • Generated on 26 February 2026
  • IMCA SF 10/14
  • 3 minute read

An incident has been bought to IMCA’s attention in which there was a small fire in the starboard engine space on a crew transfer vessel used in the offshore wind farm sector. 

What happened?

The incident occurred when on passage to an offshore wind farm. Shortly after leaving port, the fire alarm was activated in the starboard engine. Dark smoke was observed coming from the drain hole in the after inspection hatch of the starboard engine. On the CCTV into the engine space there was no indication of flames.

The starboard engine was shut down and full fire procedures were carried out. The COâ‚‚ system was also used, however on inspection after the incident it was found that the system had not deployed. Shore authorities were alerted and the vessel returned to port on one engine. All staff were safely landed ashore and the fire confirmed to be extinguished.

Investigation of the fire revealed the following:

  • Normal checks on the engines and inspection of the engine and jet spaces had been carried out before the voyage, and all was found to be in order.
  • The immediate cause of the fire was a rubber drain hose from a hatch combing catching fire as it was in contact with the exhaust system.
  • Although the drain pipe was heat resistant and the main engine exhaust was covered in thermal insulation, the drain pipe was badly positioned, crossing over the exhaust system.
  • The flames from the burning pipe were extinguished by oxygen starvation as a result of the shutdown of the engine fans and ventilators. The COâ‚‚ smothering system was not actually deployed.

The following actions were taken with regard to the fire:

  • Drain pipe on both engines replaced with a suitable thermally protected pipe which was run clear of any possible exposure to damage from the exhaust system.
  • A general focus on pipe inspections was produced and circulated.
  • Fire drills and specific vessel training to be updated to reflect lessons learnt from this incident.

Investigation of why the CO² system did not deploy revealed the following:

  • The valve to the engine space had not been opened.
  • The pin had not been removed from the valve head.
  • A brass lever had been forced in the wrong direction causing it to shear.
  • The instructions for the activation and effective use of the CO² system were not adequate to purpose.
  • They were located on the external surface of the drop down access door.
  • They are not readily visible to crew operating the system.
  • They did not highlight the need to remove the safety pin on the activation lever of the cylinder; The following actions were taken with regard to the failure to deploy the CO² smothering system.
  • Better and more detailed operating instructions issued to vessels with similar CO² smothering systems – including pictorial instructions for use.
  • Ensured that all crew members were fully conversant with the fixed fire fighting system fitted to the vessel and how to operate that fire fighting system.
Drain hole from which smoke was sighted

Drain hole from which smoke was sighted

Scorched drain pipe which was immediate cause of fire

Scorched drain pipe which was immediate cause of fire

The activation lever on the starboard cylinder was broken off, but the cylinder had not been activated

The activation lever on the starboard cylinder was broken off, but the cylinder had not been activated

Both selector valves to the port and starboard engine were in the closed position

Both selector valves to the port and starboard engine were in the closed position

Latest Safety Flashes:

Fall from height during mooring due to rope tension reaction

Rope became entangled with the propellor during mooring operations of a tanker causing the operator to lose balance and fall onto the lower platform.

Read more
Missing protection – progressive wear on hydraulic hoses causes damage

During an inspection, several hydraulic hoses and fuel hoses were found in direct contact with surrounding surfaces and sharp edges.

Read more
Small engine room fire – flammable object ignited

While ramping up the starboard main engine, a small flammable foreign object ignited.

Read more
Positive: damage to Fast Rescue Craft davit wire rope caught before failure

During routine checks, it was observed that the FRC davit wire rope had a visible fracture at the socket termination area.

Read more
BSEE: Miscommunication and trapped pressure causes injury during valve maintenance

BSEE has published Safety Alert 509 relating to a gas release incident on an offshore platform.

Read more

IMCA Safety Flashes summarise key safety matters and incidents, allowing lessons to be more easily learnt for the benefit of the entire offshore industry.

The effectiveness of the IMCA Safety Flash system depends on the industry sharing information and so avoiding repeat incidents. Incidents are classified according to IOGP's Life Saving Rules.

All information is anonymised or sanitised, as appropriate, and warnings for graphic content included where possible.

IMCA makes every effort to ensure both the accuracy and reliability of the information shared, but is not be liable for any guidance and/or recommendation and/or statement herein contained.

The information contained in this document does not fulfil or replace any individual's or Member's legal, regulatory or other duties or obligations in respect of their operations. Individuals and Members remain solely responsible for the safe, lawful and proper conduct of their operations.

Share your safety incidents with IMCA online. Sign-up to receive Safety Flashes straight to your email.